What counts as high-risk crystalline silica processing
Most silica duties in NSW switch on when processing is high risk. Here is what processing means, how businesses decide whether it is high risk, and what has to happen next.
Course and test are free. Certificate $49, paid only if you pass.
- Built to SafeWork NSW's 11 criteria
- Certificate + employer training record
- Verify by code or QR
- Secure payment by Stripe
Step 1: Is it a crystalline silica substance?
A crystalline silica substance (CSS) is any material with at least 1% crystalline silica by weight. That covers most concrete, brick, block, tile, stone, sand, mortar and fibre cement. Check the safety data sheet, and assume a high silica content for untested natural materials.
Step 2: Is it processing?
Section 529A of the WHS Regulation 2025 says processing means:
- using power tools or other mechanical plant to crush, cut, grind, trim, sand, abrasive polish or drill a CSS
- using roadheaders to excavate a CSS
- quarrying a CSS
- mechanical screening of a CSS
- tunnelling through a CSS
- any process that exposes, or is reasonably likely to expose, a person to respirable crystalline silica during the manufacture or handling of a CSS.
The silica code of practice adds that hand tools are covered if they expose, or are reasonably likely to expose, someone to silica dust. Cleaning up silica dust can be processing too.
All processing must be controlled (section 529C), whether or not it is high risk.
Step 3: Is it high risk?
Under section 5, processing is high risk if it is "reasonably likely to result in a risk to the health of a person at the workplace". The silica code explains that "reasonably likely" means more likely than not.
Section 529CA requires the PCBU to assess its processing and consider:
- the specific processing
- the form or forms of crystalline silica
- the proportion of crystalline silica in the material
- the hazards, including how often and how long people are likely to be exposed
- whether airborne silica is reasonably likely to exceed half the workplace exposure standard
- previous air and health monitoring results
- previous incidents, illnesses or diseases.
Three rules make the assessment stricter than many people expect:
- Ignore respirators and administrative controls. The assessment must not count PPE such as RPE, or administrative controls such as job rotation.
- Don't rely on the listed dust controls. The assessment can't rely on wet cutting, extraction and the other 529B(1)(b) controls to call the work low risk. The code says engineering and isolation controls may be considered, but not solely relied on.
- If unsure, it's high risk. Where the PCBU can't be sure, the processing is taken to be high risk.
The assessment must be written down.
What follows when processing is high risk
| Duty | Section |
|---|---|
| Silica risk control plan, or SWMS for high risk construction work, before work starts | 529CB |
| Follow the plan; stop and resume in line with it | 529CC (s300 for SWMS) |
| Crystalline silica training, with records kept 5 years after the worker leaves | 529CD |
| Air monitoring when exposure is uncertain; report results over the limit within 14 days | 529CE, s50 |
| Health monitoring for workers doing the processing | 529CE, Part 7.1 Div 6 |
| Register workers on the Silica Worker Register within 28 days | 529L |
Examples to think through
These are prompts for your own assessment, not rulings:
- Dry cutting pavers for several hours a day, without the listed controls counted, may well be likely to exceed half the exposure standard.
- Indoor floor grinding of concrete, where dust builds up, needs careful assessment.
- A one-off hole drilled with a small bit outdoors may come out differently. Write down why.
- Tunnelling through sandstone is listed as processing, and sandstone is 70 to 100% crystalline silica according to SafeWork NSW.
Related reading: silica risk control plan vs SWMS · the Silica Worker Register · the exposure standard · Module 11 of the free course
Frequently asked questions
Can wearing respirators make processing low risk?
No. Section 529CA says the assessment must ignore PPE, including respirators, and administrative controls.
What does "half the exposure standard" mean?
The exposure standard for respirable crystalline silica is 0.05 mg/m³ over 8 hours. One factor in the assessment is whether airborne silica is reasonably likely to exceed half of that.
Does the assessment have to be in writing?
Yes. Section 529CA requires the assessment to be written down, and it forms part of the silica risk control plan or SWMS.
What if we can't tell whether work is high risk?
Then it is taken to be high risk, and all the high-risk duties apply.
Is all processing high risk?
No. All processing must be controlled, but only processing that is reasonably likely to result in a health risk is high risk.
Sources
Last reviewed 21 November 2026. Rules can change, so check the sources for the latest.
Related
Get your silica training done today
Free course and test, built to SafeWork NSW's 11 criteria. Pay $49 only if you pass, and get your certificate and employer training record straight away.