Free online silica training course (NSW)
11 short modules, one for each of SafeWork NSW's criteria for approved crystalline silica training. Read at your own pace, check yourself as you go, then take the free test.
Course and test are free. Certificate $49, paid only if you pass.
- Built to SafeWork NSW's 11 criteria
- Certificate + employer training record
- Verify by code or QR
- Secure payment by Stripe
Who this course is for
This free online course is for workers in New South Wales who are involved in high-risk processing of crystalline silica substances, or who may be exposed to silica dust because of that processing. It is also for the supervisors who plan, run and check that work.
Under section 529CD of the WHS Regulation 2025, the business you work for (the PCBU) must give crystalline silica training to these workers. Other workers who may be exposed must still get information and instruction.
How the course is set out
The course is built to cover SafeWork NSW's 11 criteria for approved crystalline silica training. It has 11 short modules that map one-to-one to those criteria, in the same order. Module 1 covers criterion 1, module 2 covers criterion 2, and so on up to module 11. Each module includes the exact wording of its criterion, so you and your employer can see what it covers.
The course is self-paced. Most people finish it in 45 to 60 minutes.
How to use the course
- Read each module. They use plain English and examples from NSW worksites.
- Answer the two "check yourself" questions at the end of each module. Each answer explains why.
- Take the free test when you are ready. It has 20 multiple-choice questions, and you need 16 correct to pass. Every test includes at least one question on each of the 11 criteria.
There is no time limit, and you can retake the test for free as many times as you need.
What you get if you pass
After you pass, you can buy your certificate of completion for a one-off AUD $49, paid within 24 hours of passing. You also get an employer training record. It lists all 11 SafeWork NSW criteria and the module that covers each one, along with your test result, the date and a verification link.
Please note
Silica Academy is not a registered training organisation (RTO). This is non-accredited training, and it is not issued or endorsed by SafeWork NSW or any government body. Your employer decides whether this training meets its duty, and keeps the training record. At work, always follow your workplace's silica risk control plan or safe work method statement (SWMS). For health concerns, talk to a doctor or contact icare.
Health risks of silica dust
SafeWork NSW criterion 1: Identify the health risks associated with exposure to RCS, including signs and symptoms of silicosis.
Breathing in fine silica dust can cause silicosis and other serious diseases, and the damage often shows up years later.
Where the danger comes from
Crystalline silica is a natural mineral found in sand, stone, concrete, brick and many other building materials. A solid slab, brick or rock face is not harmful while it sits there. The risk starts when the material is cut, drilled, ground, sanded, polished or broken up. This work releases very fine dust called respirable crystalline silica (RCS).
"Respirable" means the particles are small enough to be breathed deep into your lungs. RCS is invisible under normal lighting and can stay in the air for a long time. A job can look clean and still put silica dust into the air you breathe.
What silicosis is
Silicosis is scarring of the lungs caused by breathing in RCS. The scarring is permanent. It cannot be reversed. Scarred lungs do not work as well, so breathing gets harder.
Two things make silicosis hard to catch early:
- symptoms may take many years to appear
- the disease can keep getting worse even after exposure stops.
Severe silicosis can lead to heart failure. Some people need a lung transplant, and it can be fatal.
Three types of silicosis
How much dust you breathe, and for how long, affects the type of silicosis that can develop.
| Type | Usual pattern of exposure |
|---|---|
| Chronic | Typically after 10 or more years of exposure |
| Accelerated | High exposure over 1 to 10 years |
| Acute | Very high exposure, usually over less than a year and sometimes just a few weeks. Acute silicosis is life-threatening. |
Accelerated and acute silicosis show that heavy exposure can cause disease within a few years, or even weeks. It is not only a risk for people at the end of a long career.
Signs and symptoms
Common symptoms of silicosis include:
- shortness of breath
- a severe cough
- general weakness.
Some workers have no symptoms at all when silicosis is first diagnosed. This is one reason health monitoring matters for workers doing high-risk processing. Regular checks can pick up changes in your lungs before you notice anything yourself. Module 11 explains when your employer must provide health monitoring.
Other diseases linked to silica dust
SafeWork NSW lists these other diseases linked to breathing RCS:
- lung cancer
- kidney disease
- chronic obstructive pulmonary disease (COPD).
Safe Work Australia also lists progressive massive fibrosis, chronic bronchitis, autoimmune disorders such as scleroderma and systemic lupus erythematosus (lupus), a higher risk of latent tuberculosis becoming active, and eye irritation or damage.
What this means on a NSW site
Think about the dusty jobs you see every week: cutting concrete slabs, chasing walls for conduit, cutting pavers, jackhammering floors during demolition, drilling into sandstone. Each one can put RCS into the air. The more dust you breathe over time, the higher your risk, and lung scarring does not heal.
You protect yourself and your crew by controlling dust at the source, keeping it away from other workers, wearing the right respirator and cleaning up safely. The rest of this course shows you how.
If you are worried about your health
This course does not give medical advice. If you have symptoms, or you are worried about dust you have breathed in the past, see a doctor and tell them about the work you do. You can also contact icare. It recommends screening every 12 months and offers subsidised screening.
Key points
- Solid stone, concrete or brick is not the danger. The fine dust released when you cut, drill, grind or polish it is.
- Respirable crystalline silica (RCS) is invisible in normal light and can stay in the air for a long time.
- Silicosis is permanent scarring of the lungs. It can keep getting worse after exposure stops.
- Silica dust is also linked to lung cancer, kidney disease and chronic obstructive pulmonary disease (COPD).
- Symptoms include shortness of breath, a severe cough and general weakness, but some people have no symptoms when first diagnosed.
Check yourself
You are chasing a brick wall with a grinder and the air looks clear. What does that tell you about silica dust?
Which type of silicosis typically develops after 10 or more years of exposure?
Which materials contain crystalline silica
SafeWork NSW criterion 2: How to determine if a material contains crystalline silica, including: (a) an explanation of the forms of crystalline silica listed in 529A of the WHS Regulation; (b) the common materials and products known to contain crystalline silica.
Most stone, concrete, brick and tile products contain crystalline silica, and anything with 1% or more counts as a crystalline silica substance under the law.
The four forms named in the law
Crystalline silica is silica in crystal form. Section 529A of the WHS Regulation 2025 says it means the crystalline polymorphs of silica, and it lists four forms:
- quartz, by far the most common form on building sites
- cristobalite
- tridymite
- tripoli.
You won't see these words on a pallet of bricks. You will see them on safety data sheets, and Module 3 explains how to read those.
The 1% rule
The law calls a material a crystalline silica substance (CSS) if it contains at least 1% crystalline silica, measured as weight for weight (w/w). Most stone, masonry and concrete products are well above 1%, so you should treat them as CSS unless the SDS shows otherwise.
Once a material is a CSS, the processing rules apply. Module 5 explains what "controlled" processing means.
Common materials and typical silica levels
SafeWork NSW gives these typical crystalline silica levels:
| Material | Typical crystalline silica |
|---|---|
| Sand and sandstone | 70 to 100% |
| Manufactured (engineered) stone | 93% or more |
| Concrete and mortar | 25 to 70% |
| Calcium-silicate bricks | 50 to 55% |
| Granite | 20 to 45% (typically 30%) |
| Slate | 20 to 40% |
| Brick | up to 30% |
| Fibre cement sheets | 10 to 30% |
| Demolition dust | 3 to 4% |
| Marble and limestone | about 2% |
These are guides only. Safe Work Australia's figures differ for some materials, which is why you should always check the SDS for the actual product. Other products that can contain silica include asphalt, pavers, blocks, grout, ceramic and porcelain tiles, sintered stone, and most rocks, sands and clays.
How to find out what you're working with
- Read the SDS. Your employer must keep the SDS for hazardous chemicals readily accessible.
- Ask the supplier if there's no SDS.
- Test natural materials. Natural stone, rock and soil can vary a lot. They should be tested by a NATA-accredited laboratory. If they haven't been, assume a high silica content.
- When in doubt, treat it as a CSS and use the controls for silica dust.
Engineered stone
Engineered stone is an artificial product made by combining natural stone materials with other ingredients such as resins or pigments, which then hardens. It can contain up to 97% crystalline silica.
Since 1 July 2024, it has been illegal in NSW to make, supply, process or install engineered stone benchtops, panels and slabs. Importing it has been banned since 1 January 2025.
Some products are not engineered stone under the law, such as concrete and cement products, bricks and pavers, ceramic tiles, grout, mortar and render, plasterboard, roof tiles, and porcelain or sintered stone without resin. These products are not banned, but many still contain silica, so the processing rules still apply.
Legacy engineered stone (stone installed before the ban) can only be processed for limited reasons, such as removal, repair, minor modification or disposal. The work must be controlled, and the business must notify SafeWork NSW in writing before the work starts. Installed benchtops are not a risk while they are left undisturbed.
Key points
- The law lists four forms of crystalline silica: quartz, cristobalite, tridymite and tripoli.
- A crystalline silica substance (CSS) is any material with at least 1% crystalline silica by weight.
- Sand, sandstone, engineered stone, concrete, mortar, brick, granite, slate and fibre cement can all contain high levels.
- Check the safety data sheet (SDS). If a natural material hasn't been tested, assume it has a high silica content.
- Engineered stone benchtops, panels and slabs have been banned since 1 July 2024.
Check yourself
A product's SDS shows it contains 2% quartz. Is it a crystalline silica substance under the WHS Regulation?
You need to cut a natural stone that has no SDS and has never been tested. What should you assume?
Safety data sheets and what 'processing' means
SafeWork NSW criterion 3: How to interpret safety data sheets (SDS) and manufacturer's information, including the meaning of 'processing' in relation to CSS as defined by section 529A of the WHS Regulation.
The safety data sheet tells you if a product contains crystalline silica and how much, and the law's definition of processing tells you when the silica rules apply.
What a safety data sheet is
A safety data sheet (SDS) is a document from the manufacturer or supplier. It explains a product's hazards and how to use it safely. Every SDS has the same 16 sections, so once you know where to look, you can check any product quickly.
Your employer must keep SDSs readily accessible. If a product has no SDS, ask the supplier for one.
Where to find silica on an SDS
Silica information usually appears in these sections:
| SDS section | What to look for |
|---|---|
| Section 2: Hazard identification | Warnings about lung damage, cancer or harm from repeated breathing of dust |
| Section 3: Composition and information on ingredients | Quartz, cristobalite, tridymite or tripoli, and the proportion of each |
| Section 8: Exposure controls and personal protection | The exposure standard and recommended controls and respirators |
| Section 11: Toxicological information | Health effects, such as silicosis and lung cancer |
In Section 3, suppliers sometimes give a range instead of an exact figure to protect commercial information. The ranges used are below 10%, 10 to below 30%, 30 to 60%, and above 60%. Any range that reaches 1% or more means the product is a crystalline silica substance.
CAS numbers
Each chemical has a CAS number, which is a unique ID. On an SDS, look for these:
- quartz: 14808-60-7
- cristobalite: 14464-46-1
- tridymite: 15468-32-3
- tripoli: 1317-95-9
If you see any of these numbers in Section 3, the product contains crystalline silica.
Manufacturer's information
Product labels, data sheets and instructions from the manufacturer can also tell you what's in a product and how to cut or drill it safely. For example, they may say which saw blade to use with water, or which dust extraction attachment fits. Follow this information, along with your workplace's silica risk control plan or safe work method statement (SWMS).
What "processing" means in the law
The silica rules apply when you process a crystalline silica substance. Section 529A of the WHS Regulation 2025 defines processing as:
- using power tools or other mechanical plant to crush, cut, grind, trim, sand, abrasive polish or drill a CSS
- using roadheaders to excavate a CSS
- quarrying a CSS
- mechanical screening of a CSS
- tunnelling through a CSS
- any other process that exposes, or is reasonably likely to expose, a person to respirable crystalline silica during the manufacture or handling of a CSS.
The last point is broad. The silica code of practice says hand tools are also covered if they expose, or are reasonably likely to expose, someone to silica dust. Cleaning up silica dust, such as sweeping or vacuuming, can itself be processing.
Putting it together on site
Before a task, ask two questions:
- Does the material contain at least 1% crystalline silica? Check the SDS (Module 2 covers common materials).
- Will the task process it? Check the list above.
If the answer to both is yes, the processing must be controlled, and the business must assess whether it is high risk. Modules 5 and 11 explain what follows.
Key points
- An SDS has 16 sections. Silica usually appears in Section 2 (hazards), Section 3 (ingredients), Section 8 (exposure controls) and Section 11 (health effects).
- Look for quartz, cristobalite, tridymite or tripoli, or their CAS numbers, such as 14808-60-7 for quartz.
- Processing includes crushing, cutting, grinding, trimming, sanding, abrasive polishing or drilling a CSS with power tools or mechanical plant.
- Tunnelling, quarrying, mechanical screening and using roadheaders also count as processing.
- Hand tools and clean-up can also be processing if they expose someone to silica dust.
Check yourself
Which SDS section lists a product's ingredients and their proportions?
Which of these is 'processing' of a crystalline silica substance under section 529A?
How silica dust is made and the exposure limit
SafeWork NSW criterion 4: How RCS is generated during processing, how workers can be exposed and the relevant workplace exposure standards for the forms of RCS.
Silica dust is made whenever a crystalline silica substance is broken up mechanically, and the legal limit for breathing it is 0.05 mg/m³ averaged over 8 hours.
How silica dust is created
Respirable crystalline silica (RCS) is created when a crystalline silica substance is broken into fine particles. Common construction tasks that do this include:
- cutting brick, concrete, stone, tiles or pavers
- angle grinding, jackhammering or chiselling concrete or masonry
- drilling, coring and chasing walls
- excavating, earthmoving and drilling rock
- road construction and tunnelling
- crushing, loading, hauling and dumping rock or tunnel spoil
- demolition
- abrasive blasting
- dry sweeping or vacuuming silica dust.
Abrasive blasting with a blasting agent that contains more than 1% crystalline silica is prohibited.
Dry methods create the most dust. A power saw cutting a paver dry can release a large cloud of fine particles in seconds. Much of the most harmful dust is too fine to see.
How workers are exposed
You are exposed when you breathe in air that contains RCS. This can happen:
- while you do the task, because the dust is released right in your breathing zone
- when you work nearby, because silica dust spreads and can stay in the air for a long time
- in enclosed spaces, such as rooms, basements and tunnels, where dust builds up
- during clean-up, especially dry sweeping or using compressed air
- from dusty clothing, when dust is shaken off later.
The more often you are exposed, and the longer each exposure lasts, the higher the risk.
The workplace exposure standard
The workplace exposure standard (WES) is the legal limit for how much RCS a worker can breathe. For all four forms of crystalline silica (quartz, cristobalite, tridymite and tripoli), it is:
0.05 mg/m³ as an 8-hour time-weighted average (TWA), measured as respirable dust.
"Time-weighted average" means the average over a full 8-hour shift. A worker must not be exposed above the standard (section 49 of the WHS Regulation 2025).
Safe Work Australia's workplace exposure standards are being renamed. From 1 December 2026, they are called workplace exposure limits (WEL). NSW adopts the new list on the same date. The value for RCS does not change: it stays at 0.05 mg/m³ (8-hour TWA).
Long shifts
The limit is set for an 8-hour day and a 40-hour week. If you work longer shifts, such as 12 hours, more than 40 hours a week, or with less than 16 hours between shifts, the limit may need to be lowered. It is never raised for shorter shifts.
How exposure is measured
Exposure is measured with air monitoring. A sampler is worn in the worker's breathing zone, outside any respirator. The sample is sent to a NATA-accredited laboratory for analysis. Module 11 explains when air monitoring is required.
A respirator can only count towards keeping a worker under the limit if all higher-order controls, such as wet cutting or extraction, are in place and the respirator is worn correctly. Respirators are never counted when the business decides whether processing is high risk.
Key points
- Cutting, grinding, drilling, crushing, polishing, blasting, excavating and sweeping all create respirable crystalline silica (RCS).
- You can be exposed by doing the task yourself or by working near someone else who is.
- The workplace exposure standard for RCS is 0.05 mg/m³ as an 8-hour time-weighted average.
- From 1 December 2026 it is called the workplace exposure limit. The value stays the same.
- For longer shifts, such as 12-hour shifts, the limit may need to be adjusted down.
Check yourself
What is the exposure standard for respirable crystalline silica?
A labourer is sweeping 10 metres away from a worker cutting pavers dry. Who could be exposed to silica dust?
What 'controlled' processing means
SafeWork NSW criterion 5: What is 'controlled' processing of CSS under section 529B of the WHS Regulation.
All processing of a crystalline silica substance must be controlled, which means using reasonably practicable controls, at least one listed dust control, and respirators for anyone still at risk.
The basic rule
Section 529C of the WHS Regulation 2025 says a business must not process a crystalline silica substance (CSS), or direct or allow a worker to do so, unless the processing is controlled. This applies to all processing of a CSS, whether or not it is high risk.
The maximum penalty for breaking this rule is 73 penalty units for an individual and 364 penalty units for a body corporate.
The three parts of "controlled"
Section 529B(1) says processing is controlled when all three of these apply:
- Controls are in place so far as is reasonably practicable. The business must do what is reasonably able to be done to eliminate or minimise the risk.
- At least one of these five controls is used:
- isolating people from the dust
- a fully enclosed operator cabin fitted with a high-efficiency air filtration system
- an effective wet dust suppression method
- an effective on-tool extraction system
- an effective local exhaust ventilation system.
- Anyone still at risk is given respiratory protective equipment (RPE) and wears it.
All three parts must be met. A respirator does not replace a dust control, and a dust control doesn't remove the need for a respirator if someone is still at risk.
When none of the five controls can be used
Section 529B(2) covers the rare case where none of the five controls is reasonably practicable. Then, providing RPE and making sure it is worn counts as controlled processing. The silica code of practice says the business should be able to show why none of the five controls was reasonably practicable.
RPE must meet Australian Standards
Section 529B(3) says any RPE used must comply with AS/NZS 1716:2012 (respiratory protective devices) and be selected, used and maintained under AS/NZS 1715:2009. Modules 7, 8 and 9 cover respirators.
The hierarchy of controls
The silica code of practice uses the hierarchy of controls. Start at the top and work down:
- Eliminate the task, for example by ordering materials pre-cut to size.
- Substitute a safer method, for example using a hand saw for autoclaved aerated concrete (AAC), or scoring and snapping tiles instead of cutting them with a power saw.
- Isolate the work, for example by doing it in a separate area away from other workers.
- Use engineering controls, such as wet cutting, on-tool extraction or local exhaust ventilation.
- Use administrative controls, such as limiting time on the task and keeping other workers away.
- Use personal protective equipment, such as RPE.
The controls at the top are the most effective. RPE is the last line of defence, because it only protects the person wearing it, and only when it fits and is worn properly.
Controlled processing on site
Here is a simple example. A concreter needs to cut a control joint in a slab.
- The saw has a water feed, so the cut is wet (a listed control).
- Other workers are kept out of the area while cutting (isolation and administrative controls).
- The concreter wears a fit-tested respirator chosen for the task (RPE for the person still at risk).
All three parts are met, so the processing is controlled. Module 6 explains how each listed control works and how to use it properly.
Key points
- Section 529C says no one may process a crystalline silica substance unless the processing is controlled.
- Controlled means three things together: reasonably practicable controls, at least one of five listed dust controls, and RPE for anyone still at risk.
- The five listed controls are isolation, an enclosed cabin with air filtration, wet suppression, on-tool extraction and local exhaust ventilation.
- RPE on its own is only acceptable if none of the five controls is reasonably practicable.
- This applies to all processing of a CSS, not just high-risk processing.
Check yourself
A worker cuts concrete with a dry saw but wears a P2 respirator. Wet cutting was available. Is the processing controlled?
Does the 'controlled processing' rule only apply to high-risk processing?
Using the five dust controls properly
SafeWork NSW criterion 6: The requirements for the controls listed in subsection 529B(1)(b) of the WHS Regulation, how they work and how to use them.
Each of the five listed dust controls only works if it is the right type, set up properly, checked before use and used the way it was designed.
1. Isolation
Isolation means separating people from the dust. Examples include:
- doing dusty work in a separate, closed-off area
- using barriers and signs to keep other workers away
- scheduling dusty tasks when fewer people are nearby
- automating a process so no one needs to stand next to it.
Isolation protects workers who aren't doing the task. The worker doing it still needs other controls.
2. Fully enclosed operator cabin with air filtration
This applies to mobile plant such as excavators, drill rigs and loaders working in silica-containing ground. To work properly, the cabin needs:
- doors and windows kept closed while working
- positive pressure of 50 to 200 pascals (under ISO 10263-4:2009), so dust is pushed out rather than drawn in
- a real-time pressure monitor with an alarm, so the operator knows if pressure drops
- HEPA filters (H13 or H14) on the air intake and, where possible, on the recirculated air.
An open window, a broken seal or a clogged filter can let dust straight into the cabin.
3. Wet dust suppression
Water binds the dust at the point where it is made. To be effective:
- use tools designed to be used with water
- make sure workers can't turn the water down or off during the task
- keep a consistent flow, usually at least 0.5 litres per minute, through a nozzle that suits the tool
- keep guards and flaps in place
- use tools with a suitable IP (water protection) rating, and manage electrical risks.
Spray bottles, sponges and garden hoses are inadequate. Water must reach the cutting point the whole time.
Wet cutting creates slurry. Clean it up before it dries, because dried slurry becomes dust again. Filter any recycled water, and watch for slips. Some wet tasks also create a fine mist that may need local exhaust ventilation as well.
4. On-tool extraction
On-tool extraction captures dust at the tool before it spreads. A system needs:
- a shroud that fits the tool and the task
- a hose that suits the vacuum
- a vacuum that is M- or H-class under AS/NZS 60335.2.69:2017.
For drills, a HEPA-filtered dust collector mounted on the tool can be used instead.
Before you start, check the shroud is the right one for the blade or bit and is undamaged, and that the hose is connected and not split. Check the vacuum's filters are clean and its airflow is working. A blocked filter or a gap at the shroud lets dust escape.
5. Local exhaust ventilation (LEV)
LEV draws dusty air away from the work and through a filter. Examples include an extraction hood on a cutting bench or a booth. LEV works best when the capture point is close to the source of the dust. Moving the work further from the hood quickly reduces how well it works.
The silica code says workers should use RPE with LEV, unless personal air monitoring shows the worker's breathing zone is below the exposure standard.
Check, use, report
For every control:
- Check it before use. Is the water flowing? Is the shroud fitted? Is the cabin door sealed?
- Use it as designed. Don't remove guards, turn off water or work outside the capture zone.
- Report faults straight away. If a control isn't working, stop and tell your supervisor.
When controls must be reviewed
Under the silica code, the business must review its controls:
- when they aren't working, including when air monitoring shows levels at or above half the exposure standard, or a health monitoring report is adverse
- before a significant change to the work
- when a health and safety representative asks
- at least every 5 years.
Key points
- Isolation keeps people away from dusty work, for example with barriers, separate areas or scheduling.
- An enclosed operator cabin needs doors and windows shut, positive pressure of 50 to 200 Pa and HEPA H13 or H14 filters.
- Wet suppression needs a tool designed for water and a steady flow, usually at least 0.5 L per minute. Spray bottles and garden hoses are not enough.
- On-tool extraction needs a shroud, a hose and an M- or H-class vacuum.
- Local exhaust ventilation works best when the capture point is close to the dust source.
Check yourself
A tiler wets the tile with a spray bottle before cutting it with a dry saw. Is this an effective wet suppression method?
What type of vacuum should an on-tool extraction system use for silica dust?
Choosing the right respirator
SafeWork NSW criterion 7: The types of respiratory protective equipment (RPE) specified by 'AS/NZS 1715:2009 Selection, use and maintenance of respiratory protective equipment', deemed as being suitable to protect against exposure to RCS.
Respirators for silica dust use particulate filters (P1, P2 or P3), and the right type depends on how much protection the task needs.
What RPE is for
Respiratory protective equipment (RPE) filters the air you breathe. For silica dust, it is the last line of defence. Dust controls such as wet cutting and extraction must come first (Module 5). RPE then protects anyone who is still at risk.
Under section 529B(3) of the WHS Regulation 2025, RPE must comply with AS/NZS 1716:2012 and be selected, used and maintained under AS/NZS 1715:2009.
Particulate filters: P1, P2 and P3
Silica dust is made of tiny solid particles, so respirators need particulate filters. AS/NZS 1715 uses three classes:
- P1: the lowest level of particulate filtration
- P2: a higher level, commonly used for silica dust
- P3: the highest level of particulate filtration.
The filter class is only part of the protection. The type of facepiece and how well it fits matter just as much.
Types of respirator
- Disposable half-face masks (for example a disposable P2 mask). Lightweight and simple, they cover the nose and mouth.
- Half facepiece with replaceable filters. A reusable rubber or silicone mask that covers the nose and mouth, with filter cartridges you replace.
- Full facepiece. Covers the whole face, including the eyes, and gives a higher level of protection.
- Powered air-purifying respirator (PAPR). A battery-powered fan pushes filtered air into a full facepiece, hood or helmet. Loose-fitting hoods and helmets don't need a tight seal on the face.
- Supplied-air respirators (such as air-hose masks). Clean air is supplied from outside the work area.
Protection factors
Each type of RPE gives a minimum protection factor (MPF). A protection factor of 10 means the respirator should reduce the dust you breathe to one-tenth of the level outside the mask. The silica code of practice gives examples:
| Protection factor needed | Suitable RPE (examples) |
|---|---|
| Up to 10 | Half facepiece with a P1, P2 or P3 filter |
| Up to 50 | Full facepiece with a P2 filter, or a PAPR with a P2 filter and any head covering or full facepiece |
| Up to 100 | Full facepiece with a P3 filter, or a full-face air-hose mask (natural breathing type) |
For higher levels of dust, a competent person must select the RPE using AS/NZS 1715.
Who chooses the respirator
The business chooses RPE based on its assessment of the task, the dust level and the worker. Safe Work Australia's guidance says RPE for silica is generally a minimum of a P2 efficiency half-face respirator, but the right type depends on the assessment. Your silica risk control plan or SWMS should say which RPE to use for each task.
Training and upkeep
The silica code says RPE training should be given when you start work and at least once a year after that, and the business's RPE program should be audited at least once a year. Learn how to put your respirator on, check its seal (Module 9), clean and store it, and know when to replace the filters.
Key points
- RPE for silica dust uses particulate filters, rated P1, P2 or P3.
- Common types are disposable masks, half facepieces with replaceable filters, full facepieces, powered air-purifying respirators (PAPR) and supplied-air respirators.
- Each type gives a minimum protection factor. The higher the dust level, the higher the protection factor needed.
- Safe Work Australia says RPE for silica is generally a minimum of a P2 half-face respirator, but the assessment decides.
- RPE is the last line of defence. It must be used with dust controls, not instead of them.
Check yourself
Which filter rating is used for particles such as silica dust?
A task needs a protection factor of up to 50. Which option suits it, according to the silica code?
Checking your respirator meets the standard
SafeWork NSW criterion 8: How to determine if RPE is compliant with the required standard 'AS/NZS 1716:2012 Respiratory protective devices'.
Compliant respirators are certified to AS/NZS 1716:2012, and you can usually confirm this from the markings on the respirator or its packaging.
Why compliance matters
Section 529B(3) of the WHS Regulation 2025 says RPE used for processing a crystalline silica substance must comply with AS/NZS 1716:2012 Respiratory protective devices. This standard sets how respirators and filters must perform. A respirator that hasn't been tested and certified may not filter silica dust as well as it claims.
How to check a respirator
- Buy from a reputable supplier. Avoid unknown sellers and products with no clear documentation.
- Confirm certification. Ask the supplier to confirm the respirator and filters are certified to AS/NZS 1716:2012.
- Look for the markings. Compliant RPE usually shows the standard number on the respirator or its packaging.
- Check overseas ratings. Some filters are rated to an overseas standard. If so, ask the manufacturer or a competent person whether they meet the Australian requirement.
- Match the filter class. Check that the filter class marked on the product (P1, P2 or P3) matches what your silica risk control plan or SWMS requires for the task.
Check before every use
A compliant respirator only protects you if it's in good condition. Before each use:
- look for cracks, tears or warping in the facepiece
- check the straps are elastic and not stretched or broken
- check the valves are clean, seated properly and undamaged
- make sure the filters are fitted correctly and are the right class
- follow the manufacturer's instructions for when to replace filters, and replace them sooner if breathing gets harder.
Disposable masks are for single shifts or as the manufacturer directs. Throw one away if it gets damaged, wet or hard to breathe through.
Don't modify your respirator
Never cut, tape, bend or alter a respirator or its filters. Changes can break the seal or the certification. If a respirator doesn't suit you, tell your supervisor so another model can be fitted and tested (Module 9).
Storage
Store reusable respirators clean and dry, away from dust, sunlight and chemicals, as the manufacturer directs. A respirator left on a dashboard or in a dusty toolbox may be damaged or dirty inside before you put it on.
Key points
- The law requires RPE used for silica to comply with AS/NZS 1716:2012.
- Buy from a reputable supplier and confirm the product is certified to the standard.
- Compliant RPE usually shows the standard number on the respirator or its packaging.
- For filters rated to an overseas standard, ask the manufacturer or a competent person.
- Check the filter class and the condition of the respirator before each use.
Check yourself
How can you usually tell if a respirator complies with AS/NZS 1716:2012?
Your new filters are marked only with an overseas rating. What should you do?
Fit testing, fit checking and facial hair
SafeWork NSW criterion 9: Fit-checking, fit-testing and facial-hair requirements for tight-fitting RPE in compliance with 'AS/NZS 1715:2009 Selection, use and maintenance of respiratory protective equipment'.
A tight-fitting respirator must be fit tested at least once a year, fit checked every time you put it on, and worn with no facial hair where it seals.
Why fit matters
A tight-fitting respirator only works if it seals against your face. Even a small gap lets dusty air leak in around the edge instead of through the filter. Faces come in many shapes and sizes, so a respirator that fits one worker may not fit another.
Fit testing
A fit test checks that a particular make, model and size of respirator seals properly on your face. It is required for tight-fitting half facepieces and full facepieces.
Fit testing must be done:
- before you first use the respirator
- for each new make, model, style or size
- when your facial features change, for example significant weight change or dental work
- at least once a year.
There are two types of fit test:
| Type | How it works | Used for |
|---|---|---|
| Qualitative | Tests whether you can taste or smell a test substance while wearing the mask | Half facepieces only |
| Quantitative | A machine measures leakage into the mask | Half and full facepieces |
The business should record the type of test, the respirator's make, model, style and size, the date and the result.
Fit checking
A fit check is a quick seal check you do yourself every time you put on a tight-fitting respirator, just before you enter an area where RPE is needed. Follow the manufacturer's instructions. There are two common methods:
- Negative pressure check: cover the filters and breathe in gently. The mask should pull in slightly and stay pulled in.
- Positive pressure check: cover the exhale valve and breathe out gently. The mask should bulge slightly without air escaping around the edges.
If you feel air leaking, adjust the straps and the position of the mask and check again. If it still leaks, don't enter the dusty area. Tell your supervisor.
A fit check doesn't replace a fit test. You need both.
Facial hair
There must be no facial hair where the mask seals, both during fit testing and every time you use the respirator. Stubble, beards and long sideburns stop the mask from sealing, even if the mask passed a fit test when you were clean shaven.
The silica code says workers who aren't clean shaven must not be given tight-fitting RPE. A practical alternative is a loose-fitting PAPR hood or helmet, which supplies filtered air without relying on a face seal and doesn't need a fit test.
Other things that can break the seal
- wearing the mask over a hat strap or hood
- glasses or other gear pressing on the edge of the mask
- straps twisted, too loose or over the wrong part of the head
- a damaged or distorted facepiece.
Put the respirator on correctly every time, and fit check before each use.
Key points
- Tight-fitting half and full facepieces must be fit tested before first use and at least once a year.
- Fit test again for a new make, model or size, or when your face changes.
- Fit check the seal every time you put the respirator on, before entering the dusty area.
- There must be no facial hair where the mask seals on your face.
- Workers who aren't clean shaven can use a loose-fitting PAPR hood or helmet, which doesn't need a fit test.
Check yourself
How often must a tight-fitting respirator be fit tested?
A worker has stubble where the mask seals. What does the silica code say?
Housekeeping and cleaning up silica dust
SafeWork NSW criterion 10: General housekeeping and cleaning methods to eliminate or minimise risk of exposure to RCS for CSS processes.
Clean up silica dust and slurry every day with wet methods or an M- or H-class vacuum, and never dry sweep or use compressed air.
Why housekeeping matters
Silica dust that settles on floors, benches, ledges and equipment doesn't stay put. It gets stirred up again by foot traffic, wind, vehicles and cleaning, and workers breathe it in. Good housekeeping removes the dust before it can be breathed in.
Cleaning up silica dust can itself be processing under the law (Module 3). Treat clean-up as a dusty task: control it and wear the RPE your plan requires.
Do
- Follow a cleaning schedule so dust doesn't build up.
- Clean up slurry and settled dust at least daily. Don't let wet slurry dry out, because dried slurry turns back into dust.
- Use wet methods: low-pressure water or wet sweeping.
- Use an M- or H-class vacuum (under AS/NZS 60335.2.69:2017) for dust on floors, surfaces and equipment.
- Clean as you go during long tasks, not just at the end of the day.
- Keep the vacuum in good order: check its filters and follow the manufacturer's instructions for emptying and maintenance, wearing RPE when you do.
Don't
- Don't use compressed air to blow dust off surfaces, equipment or clothing.
- Don't dry sweep. A broom puts fine silica dust straight back into the air.
- Don't use general-purpose vacuums, such as household or standard workshop vacuums, which can blow fine dust out through the exhaust.
- Don't use leaf blowers to clear dust.
Personal decontamination
Dust on your clothes, boots and skin can expose you and others long after the task ends.
- Vacuum dusty clothing with an M- or H-class vacuum. Never use compressed air.
- Use a laundry service if your employer provides one.
- Never take dusty workwear home. Dust shaken out at home, in the car or in the washing machine can expose your family.
- Wash your hands and face before eating, drinking or smoking, and do these away from dusty areas.
Managing waste
- Bag or contain dust and dried slurry so it can't be blown around.
- Keep waste damp or sealed until it's removed.
- Filter recycled water from wet cutting before reuse.
- Follow your site's procedures for disposing of slurry and dust.
Housekeeping on a typical site
Picture a crew cutting pavers with a wet saw on a residential job. At smoko, the slurry around the saw is shovelled up while still wet. Dust on the pavers is washed down with low pressure, not a high-pressure blast. At the end of the day, the area is wet swept, the saw table is wiped down, and the M-class vacuum is used on the tools. Nobody uses the blower. Dusty clothes are vacuumed before workers get into their cars.
Small habits like these make a big difference to how much silica dust everyone breathes.
Key points
- Clean settled dust and slurry at least daily, following a cleaning schedule.
- Use low-pressure water, wet sweeping or an M- or H-class vacuum.
- Never use compressed air, dry sweeping or a general-purpose vacuum on surfaces or clothing.
- Cleaning up silica dust can itself be processing, so control it and wear the right RPE.
- Vacuum dusty clothes with an M- or H-class vacuum and never take dusty workwear home.
Check yourself
What is the right way to clean silica dust off a concrete floor at the end of a shift?
Your work clothes are covered in dust at knock-off. What should you do?
The law: risk control plans, SWMS and monitoring
SafeWork NSW criterion 11: WHS Regulation requirements for: (a) silica risk control plans (or safe work method statements (SWMS) for construction work) under section 529CB of the WHS Regulation when undertaking processing which is high risk; (b) compliance with a silica risk control plan under section 529CC of the WHS Regulation or, for SWMS, section 300 of the WHS Regulation; (c) compliance with section 529CE including: (i) determining when air monitoring may be required under section 50 of the WHS Regulation; (ii) providing the regulator with results of any air monitoring undertaken which shows the airborne concentration of RCS has exceeded the workplace exposure standard for crystalline silica; (iii) determining when health monitoring may be required under part 7.1 division 6 of the WHS Regulation.
High-risk processing needs a written assessment, a silica risk control plan or SWMS that workers follow, air monitoring when exposure is uncertain, reporting of exceedances within 14 days, and health monitoring.
Step 1: Is the processing high risk?
Under section 5 of the WHS Regulation 2025, processing is high risk if it is reasonably likely to result in a risk to the health of a person at the workplace. Section 529CA says the business must assess its processing and consider:
- the specific processing being done
- the form or forms of crystalline silica involved
- how much crystalline silica the material contains
- the hazards, including how often and for how long people are exposed
- whether airborne silica is reasonably likely to exceed half the exposure standard
- previous air and health monitoring results
- previous incidents, illnesses or diseases.
The assessment must not count respirators or administrative controls, and must not rely on the listed dust controls. It must be in writing. If the business is unsure, the processing is taken to be high risk.
Step 2: A silica risk control plan or SWMS
Before high-risk processing starts, section 529CB requires a silica risk control plan (SRCP). It must:
- identify all high-risk processing at the workplace
- include the written assessment
- set out the controls and how they will be put in place, monitored and reviewed
- be easy to access and understand.
The silica code of practice says the plan should be developed with the workers involved and their health and safety representatives. SafeWork NSW has an optional template.
For construction work: a separate SRCP isn't needed if the processing is also high risk construction work and a safe work method statement (SWMS) that covers the same content is prepared before work starts. Construction work in an area that may have a contaminated atmosphere is high risk construction work, and silica dust can create that.
Step 3: Follow the plan
Section 529CC (and section 300 for a SWMS) says:
- the plan must be available to all workers and given to them before they start
- if work is not being done in line with the plan, it must stop immediately (or as soon as it's safe) and only resume in line with the plan
- the plan must be reviewed when controls are revised.
Step 4: Air monitoring (sections 529CE and 50)
The business must carry out air monitoring under section 50 when it isn't certain, on reasonable grounds, whether workers are exposed above the exposure standard, or when monitoring is needed to work out whether there is a health risk. Samples are taken in the worker's breathing zone and analysed by a NATA-accredited laboratory.
If results show silica dust above the exposure standard, the business must give them to SafeWork NSW as soon as reasonably practicable and within 14 days of receiving them, using SafeWork NSW's online form. This applies even if workers wore respirators. Air monitoring records must be kept for 30 years.
Step 5: Health monitoring (Part 7.1, Division 6)
Workers who do high-risk processing must be provided with health monitoring. It includes a medical and work history, a respiratory questionnaire, a lung function test and a chest X-ray, or a low-dose CT scan instead or as well. Workers who rely on respirators still need health monitoring. Reports must be kept confidential for at least 30 years.
Other NSW duties to know
- Silica Worker Register: since 1 October 2025, the business must register workers doing high-risk processing with SafeWork NSW within 28 days of starting the work.
- Training records: kept while the worker does high-risk processing and for 5 years after they leave the business.
- Codes of practice: since 1 July 2026, businesses must follow approved codes of practice, such as the silica code, or reach an equal or higher standard.
Key points
- The business must assess in writing whether processing is high risk, ignoring respirators and administrative controls. If unsure, it is high risk.
- High-risk processing needs a silica risk control plan, or a SWMS for high-risk construction work, before work starts.
- If work doesn't follow the plan or SWMS, stop and only restart in line with it.
- Air monitoring is required when exposure is uncertain. Results above the exposure standard go to SafeWork NSW within 14 days.
- Workers doing high-risk processing must get health monitoring, and be registered on the Silica Worker Register within 28 days.
Check yourself
During a job you notice the crew is cutting without the extraction listed in the SWMS. What does the law require?
Air monitoring shows silica dust above the exposure standard, although workers wore respirators. What must the business do?
Get your silica training done today
Free course and test, built to SafeWork NSW's 11 criteria. Pay $49 only if you pass, and get your certificate and employer training record straight away.